Hotline: +86 0572-5667066
NEWS
NEWS
CURRENT POSITION: HOME > NEWS
The principle and requirements of industrial pump sealing
2026-06-11 19:10

INDUSTRIAL PUMP MANUFACTURER We analyze the principles and requirements of water pump sealing for you:

1. Packing Seal

In the machinery industry, packing seal is mainly used as dynamic seal, commonly for shaft sealing of centrifugal pumps, compressors, vacuum pumps and mixers. After the packing is loaded into the packing chamber, it is axially compressed via gland bolts. When relative motion occurs between the shaft and packing, radial force generates due to packing plasticity, creating tight contact with the shaft. Meanwhile, lubricant impregnated in the packing is squeezed out to form an oil film on the contact interface.    Uneven contact creates a boundary lubrication state known as the "bearing effect" on contacting areas; recessed non-contact areas form small oil grooves with thick oil films. Contact and non-contact sections form an irregular labyrinth to block fluid leakage, which is defined as the "labyrinth effect". This is the working mechanism of packing seal.    Reliable sealing relies on stable bearing effect and labyrinth effect, namely proper lubrication and moderate compression. Poor lubrication or excessive compression will rupture the oil film, triggering dry friction between packing and shaft, and eventually shaft burning and severe abrasion.    Therefore, packing compression needs regular adjustment to replenish lubricant after loss during operation, and compensate loose compression force caused by packing volume change. Long-term repeated extrusion will exhaust impregnating agent, so periodic packing replacement is necessary. Besides, tiny controlled leakage at the packing is required to maintain liquid film and dissipate friction heat.

Defects of Packing Seal:

1. Rough packing surface brings high friction coefficient and persistent leakage; impregnated lubricant drains easily after long service.

2. Newly overhauled equipment runs well at first, yet leakage rises rapidly soon. Frequent gland adjustment and packing replacement are required. Before one service cycle ends, the shaft sleeve wears into a vase shape, even broken in severe cases. Packing behind the water seal ring decays completely and loses sealing capacity.

3. Direct contact and rotation friction between packing and shaft causes shaft & sleeve abrasion, requiring regular or unscheduled shaft sleeve replacement.

4. Certain leakage must be reserved to dissipate friction heat between packing and shaft/sleeve, which is hard to precisely control.    5. Friction consumes effective motor power and increases power consumption.

Industrial Pump Manufacturer

2. Mechanical Seal

Mechanical seal, also called end face seal, is a shaft sealing assembly for rotating machinery. It consists of at least one pair of end faces perpendicular to the rotating shaft. Under fluid pressure, elastic force (or magnetic force) of compensation components and auxiliary seal coordination, the end faces fit tightly and slide relatively to prevent fluid leakage.    It converts leak-prone axial sealing into low-leakage end face sealing, widely applied for rotary shaft sealing of pumps, reactors, compressors and analogous equipment. A standard mechanical seal includes rotating ring, stationary ring, compression parts and sealing elements.    The rotating ring spins together with the pump shaft, fitting closely with the stationary ring to form the sealing face and block medium leakage. Fluid pressure in the seal chamber presses the rotating ring end face against the stationary ring, generating proper specific pressure and an ultra-thin liquid film for sealing.    Compression parts maintain face fit even when the pump stops running, stopping medium outflow and blocking impurity ingress. Sealing elements seal gaps between rotating ring & shaft, stationary ring & gland; elastic components buffer vibration and impact on the pump.    Mechanical seals operate matched with other pump components. Stable performance depends on seal inherent quality and external working conditions. Qualified component performance, standard auxiliary seal configuration and precise installation are essential to ensure full sealing performance.

Defects of Mechanical Seal:

During operation, mechanical seal components suffer frequent failures: seal end faces wear, crack thermally, deform or rupture; springs loosen, fracture or corrode after long service; auxiliary O-rings crack, twist, deform or split.


  • Contact
    + 86 135 8826 8698
  • WeChat
  • WeChat
  • Email
  • Top